NE5534DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | NE5534 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 4mA |
| Nominal Supply Current | 4mA |
| Output Current | 38mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 500nA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~15V |
| Output Current per Channel | 38mA |
| Input Offset Voltage (Vos) | 4mV |
| Bandwidth | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=3 |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Nominal Gain Bandwidth Product | 10MHz |
| Max I/O Voltage | 4mV |
| Power | YES |
| Input Offset Current-Max (IIO) | 0.3μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NE5534DR Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are attached to buffer op amp. This linear amplifier should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. It has 8 pins that make up the linear amplifier. Op amp rates 4mV as input offset voltage. This electronic part is best mounted with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. An 4mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 100dB for the time being. The op amp ic has 1 channels on it. The linear amplifier is packaged by using a TR axis.
NE5534DR Features
8 Pins
supply voltage of 15V
100dB voltage gain
NE5534DR Applications
There are a lot of Texas Instruments NE5534DR Instrumentational OP Amps applications.
- Fission chambers
- Power transmission
- Test equipment
- Automatic control
- Band-pass filter
- High/low-pass filter circuit
- Signal filtering
- earphone
- Wireless base stations
- Communication device
