NLAS2066US
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 7Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLAS2066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Power Dissipation | 250mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 9 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 10 ns |
| -3db Bandwidth | 186MHz |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 1.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3ns, 6ns |
| Charge Injection | 7.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLAS2066US Overview
The electronic component is convenient to ship overseas because it is packed in a 8-VFSOP (0.091, 2.30mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature around -55°C~125°C TA extended. In total, there have been 8 terminations. Due to its 2 channels, the electrical component produces high-quality output. With a 2.3V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 8 series. A SPST - NO switching circuit is used for these analog switches. If you are looking for variants of the digital switch, trying search with NLAS2066. Internally, this switch multiplexer has a resistance of 7Ohm. Datasheets for 8 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. A analog switch ic that has a cost-effective Single supply type. It is recommended to use 1.65V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 1μA. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. This electrical part is compatible with 5V operating voltages.
NLAS2066US Features
2 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 186MHz
NLAS2066US Applications
There are a lot of ON Semiconductor NLAS2066US Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Battery Powered Instruments
- Channel Banks
- Switching Systems
- Mechanical reed relay replacement
- Communications systems
- E1 Network Equipment
- T1/E1 Terminals
- Medical
- ATM
