banner_page

NLAS2750MUTAG

150ns, 130ns SPDT 1.3Ohm QUAD Analog Switches BREAK-BEFORE-MAKE 10 Pins 2.7V 10-UFQFN


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-NLAS2750MUTAG
  • Package: 10-UFQFN
  • Datasheet: PDF
  • Stock: 954
  • Description: 150ns, 130ns SPDT 1.3Ohm QUAD Analog Switches BREAK-BEFORE-MAKE 10 Pins 2.7V 10-UFQFN(Kg)

Details

Tags

Parameters
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
Resistance 1.3Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 200mW
Terminal Position QUAD
Terminal Form NO LEAD
Number of Functions 2
Supply Voltage 2.7V
Terminal Pitch 0.4mm
Output SEPARATE OUTPUT
Pin Count 10
Qualification Status Not Qualified
Polarity Non-Inverting
Number of Circuits 2
Max Supply Voltage 5V
Min Supply Voltage 1.8V
Max Supply Current 250nA
Turn On Delay Time 150 ns
Supply Type Single
Turn-Off Delay Time 130 ns
-3db Bandwidth 44MHz
On-State Resistance (Max) 1.3Ohm
Multiplexer/Demultiplexer Circuit 2:1
Channel Capacitance (CS(off), CD(off)) 5pF
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 150ns, 130ns
Charge Injection 60pC
Channel-to-Channel Matching (ΔRon) 100m Ω
Crosstalk -60dB @ 300kHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.8V~5V
Height 550μm
Length 1.8mm
Width 1.4mm
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 2 days ago)
Contact Plating Gold
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 10-UFQFN
Number of Pins 10
Weight 10.007382mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2014
JESD-609 Code e4
Pbfree Code yes

NLAS2750MUTAG Overview


As the electronic part is packed in 10-UFQFN, international shipping is convenient. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. 10 terminations have been made so far. A 2.7V voltage supply should turn on and run the electronic component. A total of 10 pins are injected into the electrical part body. Circuits based on SPDT switching are used to construct these analog switch ics. 2 circuits are used in this analogue multiplexer. Analog switches have 1.3Ohm internal resistance. To find out what the 10 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 1.8V. An analogue multiplexer drains from a single voltage supply at 1.8V~5V. A voltage higher than 250nA may cause damage to the switch multiplexer. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.

NLAS2750MUTAG Features


Switch Circuit: SPDT
-3db Bandwidth: 44MHz

NLAS2750MUTAG Applications


There are a lot of ON Semiconductor NLAS2750MUTAG Analog Switches & Multiplexers ICs applications.

  • Remote Powered Equipment
  • Remote wireless modules
  • DSUs
  • Audio and video routing
  • DSLAMs
  • PDH Multiplexers
  • Avionics test equipment
  • Voice over IP/DSL – Integrated Access Devices, Smart
  • 65 V DACs
  • Relay replacements

Write a review

Note: HTML is not translated!
    Bad           Good