NLAS3799LMNR2G
| Parameters | |
|---|---|
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 400mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS3799 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 40μA |
| Max Supply Current | 10μA |
| Turn On Delay Time | 50 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 19MHz |
| On-State Resistance (Max) | 400mOhm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 30ns |
| Charge Injection | 42pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 0.8mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NLAS3799LMNR2G Overview
As the electronic part is packed in 16-WFQFN, international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:2 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 2 channels. With a 3V voltage supply, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Multiplexers built on a DPDT switching circuit are built. 2 circuits are used in this analogue multiplexer. Use NLAS3799 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 400mOhm. For details about the functions of 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 3.6V. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 1.65V should be applied to the electronic component. For this multiplexer to operate, 40μA current would be sufficient. Using a single voltage supply, this switch device consumes 1.65V~3.6V volts. A digital multiplexer may suffer damage if voltage is applied above 10μA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electronic component can function from 3V.
NLAS3799LMNR2G Features
2 Channels
Switch Circuit: DPDT
40μA Supply Current
-3db Bandwidth: 19MHz
NLAS3799LMNR2G Applications
There are a lot of ON Semiconductor NLAS3799LMNR2G Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- E1 Network Equipment
- PDH Multiplexers
- Avionics
- Avionics and Military Systems
- Battery Powered Systems
- HDTV
- Optical Applications
- Multiplexers
- Audio and video routing
