NLAS44599DT
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 30Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS44599 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 4μA |
| Power Dissipation | 450mW |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 175MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 10μA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 5ns |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
NLAS44599DT Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Operation at a temperature around -55°C~125°C TA. Totally, there are 16 terminations. A electrical component with 2 channels is capable of high-quality output. When a voltage supply of 2.5V is used, the electronic component should be turned on and run. This electrical component is included in the 16 series of products. Unlike digital switches, these are based on DPDT switching circuits. Try searching for NLAS44599 variants of the analog switch ic. Analog switches have 30Ohm internal resistance. Datasheets for 16 pin functions are available upon request. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The digital multiplexer has a low cost Single supply. It is recommended to use 2V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 4μA. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. Operating voltages range from 5V. It is possible to operate 4 inputs. There are 8 outputs on the analogue multiplexer.
NLAS44599DT Features
2 Channels
Switch Circuit: DPDT
4μA Supply Current
-3db Bandwidth: 175MHz
NLAS44599DT Applications
There are a lot of ON Semiconductor NLAS44599DT Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- CSU
- Audio/video switches
- Frame Relay Equipment
- DSUs
- USB 1.1 signal switching circuits
- Fiber to the Home
- ISDN NT1/TA
- Multi-Line E1 Interface Cards
- Avionics
