NLAS44599DTR2G
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 30Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS44599 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 4μA |
| Nominal Supply Current | 4μA |
| Power Dissipation | 450mW |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 4 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 175MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 10μA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 5ns |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NLAS44599DTR2G Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 2:2 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -55°C~125°C TA. 16 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. In the case of a voltage supply of 2.5V volts, the electrical part can be powered up and run. This electronic part can be found in the 16 series. Unlike digital switches, these are based on DPDT switching circuits. Try searching with NLAS44599 if you're looking for variants. Analog switches have 30Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Digital switch that provides Single power at a cost-effective price. 2V is the lowest voltage that should be fed to the electronic electronic part. 4μA current would be enough for this multiplexer to operate. Using a single voltage supply, this switch device consumes 2V~5.5V volts. The electronic component can function from 5V. There are 4 inputs to be operated. The analogue multiplexer has 8 outputs.
NLAS44599DTR2G Features
2 Channels
Switch Circuit: DPDT
4μA Supply Current
-3db Bandwidth: 175MHz
NLAS44599DTR2G Applications
There are a lot of ON Semiconductor NLAS44599DTR2G Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- High-Voltage
- ATM
- USB 1.1 signal switching circuits
- Relay replacements
- Communication systems
- Cross Connects
- FTTH
- Battery Powered Instruments
- SONET/SDH ADM
