Parameters |
-3db Bandwidth |
175MHz |
On-State Resistance (Max) |
25Ohm |
Multiplexer/Demultiplexer Circuit |
2:2 |
Off-state Isolation-Nom |
93 dB |
Current - Leakage (IS(off)) (Max) |
10μA |
Channel Capacitance (CS(off), CD(off)) |
10pF 10pF |
Switch Circuit |
DPDT |
Switch Time (Ton, Toff) (Max) |
14ns, 5ns |
Charge Injection |
3pC |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
41ns |
Switch-off Time-Max |
18ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Normal Position |
NC |
Height Seated (Max) |
1mm |
Length |
3mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Lifecycle Status |
OBSOLETE (Last Updated: 4 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-VFQFN Exposed Pad |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
30Ohm |
Terminal Finish |
Tin/Lead (Sn90Pb10) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
2.5V |
Terminal Pitch |
0.5mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
NLAS44599 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
5V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
4μA |
Turn On Delay Time |
35 ns |
Supply Type |
Single |
Turn-Off Delay Time |
12 ns |
NLAS44599MNR2 Overview
The electrical component comes in 16-VFQFN Exposed Pad packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:2. Around -55°C~125°C TA is the extended operating temperature. In total, there are 16 terminations. By its 2 channels, the electronic component provides high-quality output. An 2.5V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Based on DPDT switching circuits, these analog multiplexers work. This multiplexer is composed of 2 circuits. If you are looking for variants of the digital switch, trying search with NLAS44599. A 30Ohm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexers of the Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. The analogue multiplexer could operate on 4μA current. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. There are SEPARATE OUTPUT outputs on this analog switch ic. A voltage of 5V can be used to operate the electronic component.
NLAS44599MNR2 Features
2 Channels
Switch Circuit: DPDT
4μA Supply Current
-3db Bandwidth: 175MHz
NLAS44599MNR2 Applications
There are a lot of ON Semiconductor NLAS44599MNR2 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- CSU
- SDH/SONET multiplexers
- Communications systems
- Access Concentrators
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery-powered systems
- Imaging
- Automatic test equipment
- HDTV