NLAS4501DFT2G
| Parameters | |
|---|---|
| Base Part Number | NLAS4501 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Power Dissipation | 150mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 22 ns |
| -3db Bandwidth | 220MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 9ns, 10ns |
| Charge Injection | 3pC |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 25Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
NLAS4501DFT2G Overview
Shipping overseas is convenient due to the electrical component's packing in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -55°C~125°C TA. The total number of terminations is 5. A 1 channel electronic part produces high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. This electrical component is included in the 5 series of products. SPST - NO switching circuits are used in these analog switch ics. Try searching for NLAS4501 variants of the analog switch ic. As far as internal resistance is concerned, it has 25Ohm. To find out what the 5 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 2V. In order to operate this switch device, it would need a current of 1μA. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. This electrical part is compatible with 5V operating voltages.
NLAS4501DFT2G Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 220MHz
NLAS4501DFT2G Applications
There are a lot of ON Semiconductor NLAS4501DFT2G Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- ATM
- Microprocessor Controlled Analog Systems
- Remote wireless modules
- Medical Instrumentation
- PBX interfaces
- USB 1.1 signal switching circuits
- Switching Systems
- PDH Multiplexers
- Communication systems
