banner_page

NLAS4501DTT1G

9ns, 10ns SPST - NO 25Ohm DUAL Analog Switches NLAS4501 5 Pins 1nA 3V SOT-23-5 Thin, TSOT-23-5


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-NLAS4501DTT1G
  • Package: SOT-23-5 Thin, TSOT-23-5
  • Datasheet: PDF
  • Stock: 422
  • Description: 9ns, 10ns SPST - NO 25Ohm DUAL Analog Switches NLAS4501 5 Pins 1nA 3V SOT-23-5 Thin, TSOT-23-5(Kg)

Details

Tags

Parameters
Lifecycle Status LAST SHIPMENTS (Last Updated: 4 days ago)
Mounting Type Surface Mount
Package / Case SOT-23-5 Thin, TSOT-23-5
Surface Mount YES
Number of Pins 5
Operating Temperature -55°C~125°C TA
Packaging Tape & Reel (TR)
Published 2007
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 5
Resistance 25Ohm
Terminal Finish Tin (Sn)
Subcategory Multiplexer or Switches
Max Power Dissipation 200mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 3V
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number NLAS4501
Pin Count 5
Operating Supply Voltage 5V
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 2V
Operating Supply Current 1μA
Power Dissipation 200mW
Throw Configuration SPST
Turn On Delay Time 14 ns
Halogen Free Halogen Free
Supply Type Single
Turn-Off Delay Time 22 ns
-3db Bandwidth 220MHz
On-State Resistance (Max) 25Ohm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 93 dB
Current - Leakage (IS(off)) (Max) 1nA
Channel Capacitance (CS(off), CD(off)) 10pF 10pF
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 9ns, 10ns
Charge Injection 3pC
Voltage - Supply, Single (V+) 2V~5.5V
Normal Position NO
Height 1mm
Length 3mm
Width 1.5mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status RoHS Compliant
Lead Free Lead Free

NLAS4501DTT1G Overview


Due to its SOT-23-5 Thin, TSOT-23-5 packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -55°C~125°C TA. 5 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. A total of 5 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching with NLAS4501 if you're looking for variants. A 25Ohm internal resistance characterizes this multiplexer. The datasheets for the 5 pins explain the functions. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analog switch ics with Single supply type are cost-effective. A low voltage of 2V should be applied to the electronic component. For this multiplexer to operate, 1μA current would be sufficient. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. A voltage of 5V can be used to operate the electronic component.

NLAS4501DTT1G Features


1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 220MHz

NLAS4501DTT1G Applications


There are a lot of ON Semiconductor NLAS4501DTT1G Analog Switches & Multiplexers ICs applications.

  • Industrial and process control systems
  • MP3 players
  • ISDN NT1/TA
  • Microwave transmission systems
  • Imaging
  • Avionics
  • Microprocessor controlled systems
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • DSUs
  • Audio and video signal routing

Write a review

Note: HTML is not translated!
    Bad           Good