Parameters |
Lifecycle Status |
OBSOLETE (Last Updated: 4 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
10-VFDFN Exposed Pad |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
800mOhm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
NLAS4684 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
5V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
200nA |
Turn On Delay Time |
50 ns |
Supply Type |
Single |
Turn-Off Delay Time |
60 ns |
-3db Bandwidth |
9.5MHz |
On-State Resistance (Max) |
800mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
1μA |
Channel Capacitance (CS(off), CD(off)) |
102pF 104pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
30ns, 30ns |
Charge Injection |
15pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-83dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
1mm |
Length |
3mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
NLAS4684MNR2 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-VFDFN Exposed Pad. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around -55°C~125°C TA. Total terminations are 10. Due to its 1 channels, the electrical component produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. There are 10 pins injected into the electronic part body. Multiplexers built on a SPDT switching circuit are built. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with NLAS4684. There is 800mOhm internal resistance in this digital multiplexer. Please refer to the datasheets for 10 pins functions. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. A low voltage of 1.8V should be applied to the electronic component. In order to operate this switch device, it would need a current of 200nA. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. There are SEPARATE OUTPUT outputs on this analog switch ic. There is a voltage range of 5V operating voltages for the electrical part.
NLAS4684MNR2 Features
1 Channels
Switch Circuit: SPDT
200nA Supply Current
-3db Bandwidth: 9.5MHz
NLAS4684MNR2 Applications
There are a lot of ON Semiconductor NLAS4684MNR2 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- RGB switches
- Audio and video switching
- SONET/SDH ADM
- Routers
- MP3 players
- Audio signal routing
- Avionics and Military Systems
- Digital cross connects (DSX-1)
- Communication systems