NLAS4684MR2
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Terminal Finish | TIN LEAD |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 10 |
| JESD-30 Code | S-PDSO-G10 |
| Qualification Status | COMMERCIAL |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 9.5MHz |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 102pF 104pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 30ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -83dB @ 100kHz |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
NLAS4684MR2 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. An extended operating temperature of -55°C~125°C TA degrees Celsius. Total terminations are 10. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. A total of 10 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPDT switching circuits. 2 circuits are used in this analogue multiplexer. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage.
NLAS4684MR2 Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 9.5MHz
NLAS4684MR2 Applications
There are a lot of Rochester Electronics, LLC NLAS4684MR2 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Signal routing between systems
- Digital cross connects (DSX-1)
- Medical systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Isolation
- USB 1.1 signal switching circuits
- Cross Connects
- CSU
- Industrial
