Parameters |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2007 |
JESD-609 Code |
e0 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
500mOhm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
NLAS4684 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
3V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
200nA |
Turn On Delay Time |
60 ns |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
-3db Bandwidth |
9.5MHz |
On-State Resistance (Max) |
800mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
1μA |
Channel Capacitance (CS(off), CD(off)) |
102pF 104pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
30ns, 30ns |
Charge Injection |
15pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-83dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Normal Position |
NO/NC |
Height Seated (Max) |
1.1mm |
Length |
3mm |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
NLAS4684MR2 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. 2:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -55°C~125°C TA. 10 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. A 3V voltage supply should turn on and run the electronic component. A total of 10 pins are injected into the electrical part body. A SPDT switching circuit is used for these analog switches. A 2 circuit is present in this switch device. Look for analog switch ic variants by searching with NLAS4684. The internal resistance of this digital multiplexer is 500mOhm. The functions of 10 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. 1.8V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 200nA. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. A voltage of 3V can be used to operate the electronic component.
NLAS4684MR2 Features
1 Channels
Switch Circuit: SPDT
200nA Supply Current
-3db Bandwidth: 9.5MHz
NLAS4684MR2 Applications
There are a lot of ON Semiconductor NLAS4684MR2 Analog Switches & Multiplexers ICs applications.
- Cable Modem
- PBX interfaces
- Mechanical reed relay replacement
- Frame Relay Equipment
- Industrial control systems
- Sample hold systems
- Microprocessor controlled systems
- Avionics
- Automatic test equipment
- Precision test equipment