NLAS4685FCT1
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFBGA, FCBGA |
| Number of Pins | 10 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 800mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLAS4685 |
| Output | SEPARATE OUTPUT |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 200nA |
| Turn On Delay Time | 55 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 55 ns |
| -3db Bandwidth | 11.5MHz |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 208pF 102pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -81dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO/NC |
| Height Seated (Max) | 0.65mm |
| Length | 1.965mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLAS4685FCT1 Overview
Shipping overseas is convenient with the electronic component packed in 10-UFBGA, FCBGA. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -55°C~125°C TA. Total terminations are 10. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 2.5V volts, the electrical component should be turned on and run. A total of 10 pins are injected into the electrical part body. Unlike digital switches, these are based on SPDT switching circuits. The circuits in this analogue multiplexer number 2. Use NLAS4685 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 800mOhm. Datasheets for 10 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. 1.8V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 200nA would be sufficient for this switch device. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The electrical part can be operated at 5V voltage levels.
NLAS4685FCT1 Features
1 Channels
Switch Circuit: SPDT
200nA Supply Current
-3db Bandwidth: 11.5MHz
NLAS4685FCT1 Applications
There are a lot of ON Semiconductor NLAS4685FCT1 Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Precision test equipment
- Fiber to the Home
- Channel Banks
- Battery Powered Instruments
- Automotive applications
- MP3 players
- Medical systems
- Avionics and Military Systems
- Fiber In The Loop (FITL)
