NLAS4717EPFCT1G

30ns, 40ns SPDT 3.5Ohm BOTTOM Analog Switches BREAK-BEFORE-MAKE NLAS4717 10 Pins 1nA 3V 10-UFBGA, FCBGA

Manufacturer: ON Semiconductor
Nocochips NO: 598-NLAS4717EPFCT1G
Package: 10-UFBGA, FCBGA
Datasheet: PDF
Stock: 147
Description: 30ns, 40ns SPDT 3.5Ohm BOTTOM Analog Switches BREAK-BEFORE-MAKE NLAS4717 10 Pins 1nA 3V 10-UFBGA, FCBGA(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 3 days ago)
Mounting Type	Surface Mount
Package / Case	10-UFBGA, FCBGA
Surface Mount	YES
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2006
JESD-609 Code	e1
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
Resistance	2.1Ohm
Terminal Finish	Tin/Silver/Copper (Sn/Ag/Cu)
Subcategory	Multiplexer or Switches
Technology	CMOS
Terminal Position	BOTTOM
Terminal Form	BALL
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	NLAS4717
Pin Count	10
Number of Outputs	4
Operating Supply Voltage	3V
Number of Channels	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Operating Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	30 ns
Halogen Free	Halogen Free
Supply Type	Single
Turn-Off Delay Time	40 ns
-3db Bandwidth	90MHz
On-State Resistance (Max)	3.5Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	75 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	15pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	30ns, 40ns
Charge Injection	9pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-110dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	1.8V~5.5V
Normal Position	NC
Height Seated (Max)	0.65mm
Length	1.965mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

NLAS4717EPFCT1G Overview

Packed in 10-UFBGA, FCBGA, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. In total, 10 terminations have occurred. By its 2 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. An injection of 10 pins is performed into the body of the electrical component. Circuits based on SPDT switching are used to construct these analog switch ics. Try searching with NLAS4717 to find analog multiplexer variants. Analog switches have 2.1Ohm internal resistance. For details about the functions of 10 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 5.5V in normal situations. A cost-effective Single supply type analogue multiplexer. 1.8V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 1μA current. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Operating voltages of 3V are compatible with the electrical part. A analog switch ics with 4 outputs is included.