NLAS4717EPMTR2G
| Parameters | |
|---|---|
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 4.5Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS4717 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 30 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 40ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFQFN |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e4 |
NLAS4717EPMTR2G Overview
The electrical component comes in 10-WFQFN packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. There are 10 terminations totally. This electronic part offers high-quality output due to its 2 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 10 pins. Based on SPDT switching circuits, these analog multiplexers work. Try searching for NLAS4717 variants of the analog switch ic. There is 4.5Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 10 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Single supply type digital switch with a low cost. 1.8V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 1μA current. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. 3V operating voltages are supported by the electronic component. In this digital multiplexer, there are 4 outputs.
NLAS4717EPMTR2G Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 90MHz
NLAS4717EPMTR2G Applications
There are a lot of ON Semiconductor NLAS4717EPMTR2G Analog Switches & Multiplexers ICs applications.
- Modems
- Industrial
- Precision instrumentation
- DVD-R
- Precision test equipment
- Cable PC
- Audio and video switching
- USB 1.1 signal switching circuits
- 65 V DACs
- Cross Connects
