NLAS4717FCT1G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFBGA, FCBGA |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 2.1Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS4717 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 30 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 40MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 40ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height Seated (Max) | 0.65mm |
| Length | 1.965mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLAS4717FCT1G Overview
Due to its 10-UFBGA, FCBGA packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. In total, there have been 10 terminations. A electrical component with 2 channels is capable of high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. A total of 10 pins are injected into the electrical part body. Circuits based on SPDT switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with NLAS4717. In this multiplexer, the internal resistance is 2.1Ohm. Datasheets for functions of 10 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 5.5V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. For this digital switch to work, 1μA current would suffice. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. Operating voltages of 5V are compatible with the electrical part. 4 outputs are included in the analogue multiplexer.
NLAS4717FCT1G Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 40MHz
NLAS4717FCT1G Applications
There are a lot of ON Semiconductor NLAS4717FCT1G Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Remote Powered Equipment
- FTTH
- Avionics test equipment
- Public switching systems
- USB 1.1 signal switching circuits
- Wireless Local Loop
- Microprocessor controlled systems
- Fiber to the Home
- DVD-R
