Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2005 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
2.1Ohm |
Terminal Finish |
Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
NLAS4717 |
Pin Count |
10 |
Number of Outputs |
4 |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
30 ns |
Halogen Free |
Halogen Free |
Supply Type |
Single |
Turn-Off Delay Time |
40 ns |
-3db Bandwidth |
40MHz |
On-State Resistance (Max) |
3.5Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
30pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
30ns, 40ns |
Charge Injection |
9pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-110dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Normal Position |
NC |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
NLAS4717MR2G Overview
Packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 10. As a result of its 2 channels, this electronic component provides high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. A key feature of the 10 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching with NLAS4717 to find analog multiplexer variants. Analog switches have 2.1Ohm internal resistance. The functions of 10 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. 1.8V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 1μA current. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. This digital multiplexer has 4 outputs.
NLAS4717MR2G Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 40MHz
NLAS4717MR2G Applications
There are a lot of ON Semiconductor NLAS4717MR2G Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- E1 Network Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Frame Relay Equipment
- Microprocessor Controlled Analog Systems
- Industrial control systems
- Avionics
- Transmit
- T1/E1 Terminals
- PCMCIA cards