NLAS5113MUTBG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.3Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 4.2V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | NLAS5113 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 4.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 7 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 4.5 ns |
| -3db Bandwidth | 457MHz |
| On-State Resistance (Max) | 1.3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 7ns, 4.5ns |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.55mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | OBSOLETE (Last Updated: 2 weeks ago) |
NLAS5113MUTBG Overview
As the electronic part is packed in 6-UFDFN, international shipping is convenient. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around -40°C~85°C TA is the extended operating temperature. The total number of terminations is 6. A high-quality output is provided by the electrical component's 1 channels. Powered by a 4.2V voltage supply, the electrical part should be switched on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. Based on SPST - NO switching circuits, these analog multiplexers work. A total of 1 circuits make up this switch device. Try searching with NLAS5113 to find analog multiplexer variants. A 1.3Ohm internal resistance characterizes this multiplexer. Datasheets for 6 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 4.5V volts for the multiplexer. The digital multiplexer has a low cost Single supply. It is recommended to use 1.65V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. Analogue multiplexers require a 1.65V~4.5V voltage to drain from a single voltage supply. There is a voltage range of 3V operating voltages for the electrical part.
NLAS5113MUTBG Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 457MHz
NLAS5113MUTBG Applications
There are a lot of ON Semiconductor NLAS5113MUTBG Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Private Branch Exchange (PBX)
- Video switching
- 65 V DACs
- Audio and video signal routing
- Digital access cross connects
- Automatic test equipment
- Microwave transmission systems
- High reliability control systems
- Power routing
