NLAS5123MNR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-WFDFN |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS5123 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 500nA |
| Turn On Delay Time | 30 ns |
| Number of Inputs | 1 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 20 ns |
| -3db Bandwidth | 55MHz |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 20pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 20ns, 15ns |
| Charge Injection | 48pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 35ns |
| Voltage - Supply, Single (V+) | 1.65V~4.5V |
| Height | 750μm |
| Length | 1.2mm |
| Width | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLAS5123MNR2G Overview
Shipping overseas is convenient due to the electrical component's packing in 6-WFDFN. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 2.7V voltage supply, the electrical part should be switched on and run. A total of 6 pins are injected into the electrical part body. These analog multiplexers are built based on SPDT switching circuits. Try searching for the analog switch ic with NLAS5123 if you are looking for variants. In this multiplexer, the internal resistance is 1Ohm. You can find the functions of the 6 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. In order for the electronic part to function properly, the lowest voltage should be 1.65V. This digital switch can be operated with a current of 500nA. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~4.5V. The electrical part can be operated at 5V voltage levels. It is possible to operate 1 inputs. 2 outputs are included in the analogue multiplexer.
NLAS5123MNR2G Features
1 Channels
Switch Circuit: SPDT
500nA Supply Current
-3db Bandwidth: 55MHz
NLAS5123MNR2G Applications
There are a lot of ON Semiconductor NLAS5123MNR2G Analog Switches & Multiplexers ICs applications.
- Cable PC
- Low-Voltage
- Industrial
- Data Acquisition Systems
- Fault Tolerant Systems
- Relay Replacement
- Ultrasound
- High-Voltage
- E1 Network Equipment
- Medical
