banner_page

NLAS5213AMUTAG

20ns, 15ns DPST - NO 1.3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE NLAS5213 8 Pins 3.3V 8-UFDFN


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-NLAS5213AMUTAG
  • Package: 8-UFDFN
  • Datasheet: PDF
  • Stock: 737
  • Description: 20ns, 15ns DPST - NO 1.3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE NLAS5213 8 Pins 3.3V 8-UFDFN(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status LAST SHIPMENTS (Last Updated: 2 days ago)
Mounting Type Surface Mount
Package / Case 8-UFDFN
Surface Mount YES
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 1.3Ohm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Terminal Position DUAL
Number of Functions 1
Supply Voltage 3.3V
Terminal Pitch 0.4mm
Base Part Number NLAS5213
Pin Count 8
Operating Supply Voltage 3V
Number of Channels 1
Number of Circuits 1
Max Supply Voltage 4.5V
Min Supply Voltage 1.65V
Operating Supply Current 1μA
Throw Configuration DPST
Turn On Delay Time 20 ns
Number of Inputs 2
Halogen Free Halogen Free
Supply Type Single
Turn-Off Delay Time 15 ns
-3db Bandwidth 496MHz
On-State Resistance (Max) 1.3Ohm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 57 dB
Channel Capacitance (CS(off), CD(off)) 19pF
On-state Resistance Match-Nom 0.16Ohm
Switch Circuit DPST - NO
Switch Time (Ton, Toff) (Max) 20ns, 15ns
Channel-to-Channel Matching (ΔRon) 150m Ω
Crosstalk -97dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.65V~4.5V
Height Seated (Max) 0.55mm
Radiation Hardening No
RoHS Status RoHS Compliant
Lead Free Lead Free

NLAS5213AMUTAG Overview


The electronic part can be shipped overseas conveniently because it is packaged in 8-UFDFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. There are 8 terminations totally. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. Into the electrical component body are injected 8 pins. Unlike digital switches, these are based on DPST - NO switching circuits. Circuits number 1 make up this analogue multiplexer. Try searching with NLAS5213 if you're looking for variants. A 1.3Ohm internal resistance characterizes this multiplexer. The datasheets for the 8 pins explain the functions. Multiplexer or Switches is a typical switch device. A voltage higher than 4.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. Using a single voltage supply, this switch device consumes 1.65V~4.5V volts. 3V operating voltages are supported by the electronic component. It is possible to operate 2 inputs.

NLAS5213AMUTAG Features


1 Channels
Switch Circuit: DPST - NO
1μA Supply Current
-3db Bandwidth: 496MHz

NLAS5213AMUTAG Applications


There are a lot of ON Semiconductor NLAS5213AMUTAG Analog Switches & Multiplexers ICs applications.

  • HDTV
  • Power routing
  • Industrial and process control systems
  • E1 Multiplexer
  • Avionics test equipment
  • Precision instrumentation
  • Central office
  • Modems
  • SDH
  • Communication systems

Write a review

Note: HTML is not translated!
    Bad           Good