banner_page

NLAS5213BMUTAG

20ns, 15ns SPST - NO 1.3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE NLAS5213 8 Pins 3.3V 8-UFDFN


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-NLAS5213BMUTAG
  • Package: 8-UFDFN
  • Datasheet: PDF
  • Stock: 953
  • Description: 20ns, 15ns SPST - NO 1.3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE NLAS5213 8 Pins 3.3V 8-UFDFN(Kg)

Details

Tags

Parameters
Length 1.8mm
Width 1.2mm
Radiation Hardening No
RoHS Status RoHS Compliant
Lead Free Lead Free
Lifecycle Status LAST SHIPMENTS (Last Updated: 1 day ago)
Mounting Type Surface Mount
Package / Case 8-UFDFN
Surface Mount YES
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 1.3Ohm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Terminal Position DUAL
Number of Functions 2
Supply Voltage 3.3V
Terminal Pitch 0.4mm
Base Part Number NLAS5213
Pin Count 8
Number of Outputs 2
Operating Supply Voltage 3V
Number of Channels 2
Max Supply Voltage 4.5V
Min Supply Voltage 1.65V
Operating Supply Current 1μA
Nominal Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 20 ns
Halogen Free Halogen Free
Supply Type Single
Turn-Off Delay Time 15 ns
-3db Bandwidth 496MHz
On-State Resistance (Max) 1.3Ohm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 57 dB
Channel Capacitance (CS(off), CD(off)) 19pF
On-state Resistance Match-Nom 0.16Ohm
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 20ns, 15ns
Channel-to-Channel Matching (ΔRon) 150m Ω
Crosstalk -97dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.65V~4.5V
Height 500μm

NLAS5213BMUTAG Overview


Due to its 8-UFDFN packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 8. High-quality output is provided by the electronic component's 2 channels. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. It is part of the design of the 8 series that this electronic component is included. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for NLAS5213 variants of the analog switch ic. A 1.3Ohm internal resistance characterizes this multiplexer. To find out what the 8 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 4.5V. The digital multiplexer has a low cost Single supply. In order for the electronic part to function properly, the lowest voltage should be 1.65V. It would be sufficient to run this analogue multiplexer with 1μA current. The voltage required by this switch device is 1.65V~4.5V, draining from a single voltage supply. 3V operating voltages are supported by the electronic component. An output of 2 is provided by the digital multiplexer.

NLAS5213BMUTAG Features


2 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 496MHz

NLAS5213BMUTAG Applications


There are a lot of ON Semiconductor NLAS5213BMUTAG Analog Switches & Multiplexers ICs applications.

  • Communication systems
  • Video switching
  • Automatic test equipment
  • Communications systems
  • Digital cross connects (DSX-1)
  • Battery Powered Systems
  • 65 V DACs
  • Data switching
  • Industrial and process control systems
  • Audio and video switching

Write a review

Note: HTML is not translated!
    Bad           Good