NLAS5223BMUR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 400mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Base Part Number | NLAS5223 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 4.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 2 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 19MHz |
| On-State Resistance (Max) | 350mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 500nA |
| Channel Capacitance (CS(off), CD(off)) | 60pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 50ns |
| Charge Injection | 38pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -70dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.5V |
| Height Seated (Max) | 0.6mm |
| Length | 1.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLAS5223BMUR2G Overview
The electronic component is convenient to ship overseas because it is packed in a 10-UFQFN. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 10 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. It is part of the design of the 10 series that this electronic component is included. On the other hand, analog switches can be constructed using SPDT switching circuits. Search with NLAS5223 if you are looking for analog multiplexer variants. It has an internal resistance of 400mOhm. The datasheets for the 10 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 4.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. It is recommended to use 1.65V as the lowest voltage for the electrical part. This multiplexer would work with 1μA current. Using only a single voltage supply, this analog switch requires 1.65V~4.5V voltage. It may damage the digital multiplexer if the voltage is higher than 1μA. A voltage of 3V can be used to operate the electronic component. Among the inputs that can be operated are the 2 inputs. The analog switch ics includes 4 outputs.
NLAS5223BMUR2G Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 19MHz
NLAS5223BMUR2G Applications
There are a lot of ON Semiconductor NLAS5223BMUR2G Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Automatic test equipment
- Intelligent PBX
- PBXs
- Frame Relay Equipment
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Microwave transmission systems
- Audio and video switching
- ISDN NT1/TA
- Voice over IP/DSL – Integrated Access Devices, Smart
