NLAS5223LMNR2G
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-WFQFN |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 300mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS5223 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 17MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500nA |
| Channel Capacitance (CS(off), CD(off)) | 75pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 30ns |
| Charge Injection | 38pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -70dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height Seated (Max) | 0.8mm |
| Length | 1.8mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NLAS5223LMNR2G Overview
The electrical component comes in 10-WFQFN packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 10. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. This electronic part can be found in the 10 series. Circuits based on SPDT switching are used to construct these analog switch ics. NLAS5223 can be used to search for analog multiplexer variants. Analog switches have 300mOhm internal resistance. Datasheets for 10 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 3.6V. A cost-effective Single supply type analogue multiplexer. It is recommended to use 1.65V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. A voltage of 1.65V~3.6V is required to drain this analog switch from a single voltage supply. The electronic component can function from 3V. Among the inputs that can be operated are the 2 inputs. A analog switch ics with 4 outputs is included.
NLAS5223LMNR2G Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 17MHz
NLAS5223LMNR2G Applications
There are a lot of ON Semiconductor NLAS5223LMNR2G Analog Switches & Multiplexers ICs applications.
- Data switching
- Audio and video signal routing
- Cable Modem
- PDAs
- SDH/SONET multiplexers
- Relay replacements
- RGB switches
- CSU
- Mechanical reed relay replacement
- Transmit
