NLAS5223MNR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 21 hours ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-WFQFN |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS5223 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 2μA |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 2 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 17MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500nA |
| Channel Capacitance (CS(off), CD(off)) | 75pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 30ns |
| Charge Injection | 38pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -70dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height Seated (Max) | 0.8mm |
| Length | 1.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLAS5223MNR2G Overview
Presented in 10-WFQFN, this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. In total, 10 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. As part of its design, the 10 series is equipped with this electronic component. A SPDT switching circuit is used to build these analog multiplexers. Try searching with NLAS5223 if you're looking for variants. As far as internal resistance is concerned, it has 300mOhm. To find out what the 10 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 3.6V. The analog switch ic is of the Single supply type and is cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. It would be sufficient to run this analogue multiplexer with 1μA current. Analogue multiplexers require a 1.65V~3.6V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 2μA. It can operate from 3V operating voltages. In order to operate the 2 inputs, there are several steps to follow. The analog switch ics includes 4 outputs.
NLAS5223MNR2G Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 17MHz
NLAS5223MNR2G Applications
There are a lot of ON Semiconductor NLAS5223MNR2G Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- PDH Multiplexers
- HDTV
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- RGB switches
- Transmit
- Precision instrumentation
- Communication systems
- Frame Relay Equipment
