Parameters |
Lifecycle Status |
LAST SHIPMENTS (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-WFQFN |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2006 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
30Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Number of Functions |
2 |
Supply Voltage |
2.5V |
Base Part Number |
NLAS9431 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
4μA |
Nominal Supply Current |
8μA |
Power Dissipation |
800mW |
Turn On Delay Time |
35 ns |
Number of Inputs |
4 |
Halogen Free |
Halogen Free |
Supply Type |
Single |
Bandwidth |
170MHz |
Turn-Off Delay Time |
12 ns |
-3db Bandwidth |
175MHz |
On-State Resistance (Max) |
25Ohm |
Multiplexer/Demultiplexer Circuit |
2:2 |
Off-state Isolation-Nom |
93 dB |
Current - Leakage (IS(off)) (Max) |
10μA |
Channel Capacitance (CS(off), CD(off)) |
10pF 10pF |
Switch Circuit |
DPDT |
Switch Time (Ton, Toff) (Max) |
14ns, 5ns |
Charge Injection |
3pC |
Crosstalk |
-98dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
18ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Height Seated (Max) |
0.8mm |
Radiation Hardening |
No |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
NLAS9431MTR2G Overview
The electrical component comes in 16-WFQFN packaging, which makes it convenient to ship overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. 2:2 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -55°C~125°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 2 channels. A 2.5V voltage supply should turn on and run the electronic component. As part of the design of the 16 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on DPDT switching circuits. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with NLAS9431. An switch multiplexer with 30Ohm internal resistance has a value of 30Ohm. The datasheets for the 16 pins explain the functions. This switch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 2V. For this multiplexer to operate, 4μA current would be sufficient. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The electrical part can be operated at 5V voltage levels. It is possible to operate 4 inputs. This switch operates within the bandwidth of 170MHz.
NLAS9431MTR2G Features
2 Channels
Switch Circuit: DPDT
4μA Supply Current
-3db Bandwidth: 175MHz
Bandwidth: 170MHz
NLAS9431MTR2G Applications
There are a lot of ON Semiconductor NLAS9431MTR2G Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- FTTH
- Audio and video routing
- E1 Network Equipment
- Digital Cross-Connects
- Industrial
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Mechanical reed relay replacement
- Data Acquisition Systems