NLASB3157DFT2
| Parameters | |
|---|---|
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 7Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLASB3157 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Operating Supply Current | 1μA |
| Propagation Delay | 1.2 ns |
| Turn On Delay Time | 23 ns |
| Supply Type | Single |
| Bandwidth | 250MHz |
| Turn-Off Delay Time | 12.5 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6.5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 5.2ns, 3.5ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -54dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 24ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Length | 2mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Lifecycle Status | OBSOLETE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
NLASB3157DFT2 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 6-TSSOP, SC-88, SOT-363. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -55°C~125°C TA are extended for operation. 6 terminations have been made so far. A high-quality output is provided by the electrical component's 2 channels. With a 2.3V voltage supply, the electrical component should be turned on and run. A total of 6 pins are injected into the electrical part body. Unlike digital switches, these are based on SPDT switching circuits. The multiplexer consists of 1 circuits. Try searching for NLASB3157 variants of the analog switch ic. In this multiplexer, the internal resistance is 7Ohm. You can find the functions of the 6 pins in the datasheets. Multiplexer or Switches is a typical switch device. Single supply type digital switch with a low cost. 1μA current would be enough for this multiplexer to operate. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. Operating voltages range from 5.5V. The data can be transferred over a wide range of bandwidths, called 250MHz bandwidths.
NLASB3157DFT2 Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 250MHz
NLASB3157DFT2 Applications
There are a lot of ON Semiconductor NLASB3157DFT2 Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Audio and video switching
- SDH
- Remote wireless modules
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Mechanical reed relay replacement
- Voice over IP/DSL – Integrated Access Devices, Smart
- Medical Instrumentation
- Channel Banks
- Microprocessor Controlled Analog Systems
