NLASB3157DFT2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 4.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLASB3157 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 180mW |
| Propagation Delay | 1.2 ns |
| Turn On Delay Time | 23 ns |
| Number of Inputs | 1 |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Bandwidth | 250MHz |
| Turn-Off Delay Time | 12.5 ns |
| On-State Resistance (Max) | 7Ohm |
| High Level Output Current | 128mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6.5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 5.2ns, 3.5ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -54dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLASB3157DFT2G Overview
Presented in 6-TSSOP, SC-88, SOT-363, this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Around -55°C~125°C TA is the extended operating temperature. In total, there are 6 terminations. A high-quality output is provided by the electrical component's 2 channels. An 2.3V voltage supply should allow the electrical part to be turned on and run. A total of 6 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPDT switching circuits. Try searching with NLASB3157 to find analog multiplexer variants. As far as internal resistance is concerned, it has 4.5Ohm. Please refer to the datasheets for 6 pins functions. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 1.65V. The switch device would be able to operate with 1μA current. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. Operating 1 inputs is required. 250MHz bandwidths enable data to be transferred. The analogue multiplexer has 2 outputs.
NLASB3157DFT2G Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 250MHz
NLASB3157DFT2G Applications
There are a lot of ON Semiconductor NLASB3157DFT2G Analog Switches & Multiplexers ICs applications.
- Optical Applications
- 65 V DACs
- Intelligent PBX
- E1 Multiplexer
- Modems
- PDH Multiplexers
- Digital access cross connects
- Residential Gateways, Home Gateway/Router
- Voice over IP/DSL – Integrated Access Devices, Smart
- SDH
