Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
6-WFDFN |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2006 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Resistance |
17Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
180mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.4mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
NLASB3157 |
Pin Count |
6 |
Number of Outputs |
2 |
Operating Supply Voltage |
3V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
1μA |
Power Dissipation |
180mW |
Turn On Delay Time |
23 ns |
Number of Inputs |
1 |
Halogen Free |
Halogen Free |
Supply Type |
Single |
Turn-Off Delay Time |
12.5 ns |
-3db Bandwidth |
250MHz |
On-State Resistance (Max) |
7Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
57 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
6.5pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
5.2ns, 3.5ns |
Charge Injection |
7pC |
Channel-to-Channel Matching (ΔRon) |
150m Ω |
Crosstalk |
-54dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Height Seated (Max) |
0.8mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
NLASB3157MTR2G Overview
Due to its 6-WFDFN packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -55°C~125°C TA extended. Total terminations are 6. The electronic part delivers high-quality output through its 2 channels. A 2.3V voltage supply should turn on and run the electronic component. It is part of the design of the 6 series that this electronic component is included. Based on SPDT switching circuits, these analog multiplexers work. If you are looking for variants of the digital switch, trying search with NLASB3157. An switch multiplexer with 17Ohm internal resistance has a value of 17Ohm. Please refer to the datasheets for 6 pins functions. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analog switch ics with Single supply type are cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. The analogue multiplexer could operate on 1μA current. An analogue multiplexer drains from a single voltage supply at 1.65V~5.5V. Operating voltages range from 3V. The electrical component supports 1 inputs. In this digital multiplexer, there are 2 outputs.
NLASB3157MTR2G Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 250MHz
NLASB3157MTR2G Applications
There are a lot of ON Semiconductor NLASB3157MTR2G Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- High reliability control systems
- Residential Gateways, Home Gateway/Router
- Industrial control systems
- RGB switches
- Fault Tolerant Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial and process control systems
- Remote Powered Equipment
- Audio and video signal routing