NLAST44599DT
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 30Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | NLAST44599 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 4μA |
| Power Dissipation | 450mW |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 175MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 5ns |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
NLAST44599DT Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. In Surface Mount, this analog switch is mounted. There is 2:2 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -55°C~125°C TA. There are 16 terminations totally. This electronic part offers high-quality output due to its 2 channels. It is safe to turn on and run the electronic component with a 2.5V voltage supply. There is an electrical component included in the 16 series. Based on DPDT switching circuits, these analog multiplexers work. Using the NLAST44599 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 30Ohm. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analogue multiplexer with a Single supply type that is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 4μA. Using a single voltage supply, this switch device consumes 2V~5.5V volts. The electrical part can be operated at 5V voltage levels. A 4 input needs to be operated. The analog switch ics includes 8 outputs.
NLAST44599DT Features
2 Channels
Switch Circuit: DPDT
4μA Supply Current
-3db Bandwidth: 175MHz
NLAST44599DT Applications
There are a lot of ON Semiconductor NLAST44599DT Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Audio and video routing
- Multi-Line E1 Interface Cards
- Mechanical reed relay replacement
- Fiber In The Loop (FITL)
- Video signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Routers
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Cable Modem
