NLAST44599DTR2
| Parameters | |
|---|---|
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 30Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAST44599 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 4μA |
| Power Dissipation | 450mW |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 175MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 5ns |
| Charge Injection | 3pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
NLAST44599DTR2 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:2. Increasing operating temperature to around -55°C~125°C TA. There are 16 terminations totally. As a result of its 2 channels, this electronic component provides high-quality output. When a voltage supply of 2.5V is used, the electronic component should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Circuits based on DPDT switching are used to construct these analog switch ics. NLAST44599 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 30Ohm. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 2V. For this digital switch to work, 4μA current would suffice. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. The electrical part can be operated at 5V voltage levels. In order to operate the 4 inputs, there are several steps to follow. Multiplexer ics with 8 outputs are available.
NLAST44599DTR2 Features
2 Channels
Switch Circuit: DPDT
4μA Supply Current
-3db Bandwidth: 175MHz
NLAST44599DTR2 Applications
There are a lot of ON Semiconductor NLAST44599DTR2 Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Data Acquisition Systems
- Avionics and Military Systems
- Microprocessor Controlled Analog Systems
- CSU
- Cell phones
- Digital cross connects (DSX-1)
- ISDN NT1/TA
- SDH
- Intelligent PBX
