NLAST4501DTT1
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn80Pb20) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLAST4501 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 22 ns |
| -3db Bandwidth | 220MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 9ns, 10ns |
| Charge Injection | 3pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLAST4501DTT1 Overview
Shipping overseas is convenient with the electronic component packed in SOT-23-5 Thin, TSOT-23-5. The advanced packaging method Tape & Reel (TR) provides high reliability. Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -55°C~125°C TA is the extended operating temperature. A total of 5 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. There is an electrical component included in the 5 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. A 1 circuit is present in this switch device. NLAST4501 can be used to search for analog multiplexer variants. It has an internal resistance of 30Ohm. For details about the functions of 5 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. A analog switch ic that has a cost-effective Single supply type. 2V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. A voltage higher than 1μA may cause damage to the switch multiplexer. This electrical part is compatible with 5V operating voltages.
NLAST4501DTT1 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 220MHz
NLAST4501DTT1 Applications
There are a lot of ON Semiconductor NLAST4501DTT1 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Digital access cross connects
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Wireless Local Loop
- ATM
- PDAs
- Low-Voltage
- Precision test equipment
- SONET/SDH ADM
- Frame Relay Equipment
