NLAST4599DTT1G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAST4599 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Leakage Current | 1mA |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 200mW |
| Turn On Delay Time | 28 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 12 ns |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Height | 1mm |
| Length | 3.1mm |
| Width | 1.7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLAST4599DTT1G Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-23-6 Thin, TSOT-23-6. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature extended to -55°C~125°C TA. Totally, there are 6 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 6 series. SPDT switching circuits are used in these analog switch ics. Try searching for the analog switch ic with NLAST4599 if you are looking for variants. This digital multiplexer has 30Ohm internal resistance. You can find the functions of the 6 pins in the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2V. This digital switch can be operated with a current of 1μA. Using a single voltage supply, this switch device consumes 2V~5.5V volts. 200MHz bandwidths enable data to be transferred. The analog switch ics includes 2 outputs.
NLAST4599DTT1G Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 200MHz
NLAST4599DTT1G Applications
There are a lot of ON Semiconductor NLAST4599DTT1G Analog Switches & Multiplexers ICs applications.
- Isolation
- Automatic test equipment
- Microprocessor Controlled Analog Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Signal routing between systems
- Transmit
- Frame Relay Equipment
- Digital cross connects (DSX-1)
- Industrial and process control systems
- SDH
