NLVAS4599DFT2
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn80Pb20) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLVAS4599 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 28 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 220MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Length | 2mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLVAS4599DFT2 Overview
Due to its 6-TSSOP, SC-88, SOT-363 packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. An extended operating temperature of -55°C~125°C TA degrees Celsius. Total terminations are 6. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPDT switching circuits. The circuits in this analogue multiplexer number 1. Try searching with NLVAS4599 to find analog multiplexer variants. Analog switches have 30Ohm internal resistance. Datasheets for functions of 6 pins are available. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analog switch ics with Single supply type are cost-effective. It is recommended to use 2V as the lowest voltage for the electrical part. For this multiplexer to operate, 1μA current would be sufficient. This analogue multiplexer requires a voltage of 2V~5.5V when it drains from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. 5V operating voltages are supported by the electronic component. Automotive, AEC-Q100 is a series number.
NLVAS4599DFT2 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 220MHz
NLVAS4599DFT2 Applications
There are a lot of ON Semiconductor NLVAS4599DFT2 Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Mechanical reed relay replacement
- ISDN NT1/TA
- DVD-R
- Medical systems
- Residential Gateways, Home Gateway/Router
- Cross Connects
- USB 1.1 signal switching circuits
- PCMCIA cards
- New designs requiring multiplexer functions
