Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
6-TSSOP, SC-88, SOT-363 |
Surface Mount |
YES |
Number of Pins |
6 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2005 |
Series |
Automotive, AEC-Q100 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Resistance |
30Ohm |
Terminal Finish |
Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
200mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
4.5V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
NLVAS4599 |
Pin Count |
6 |
Number of Outputs |
2 |
Operating Supply Voltage |
5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Power Dissipation |
200mW |
Turn On Delay Time |
28 ns |
Number of Inputs |
1 |
Supply Type |
Single |
Turn-Off Delay Time |
12 ns |
-3db Bandwidth |
220MHz |
On-State Resistance (Max) |
25Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
93 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
10pF 10pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
14ns, 8ns |
Charge Injection |
3pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
30ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Height |
990.6μm |
Length |
2.1844mm |
Width |
1.3462mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
NLVAS4599DFT2G Overview
As the electronic part is packed in 6-TSSOP, SC-88, SOT-363, international shipping is convenient. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -55°C~125°C TA. A total of 6 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 4.5V volts, the electrical part can be powered up and run. As part of its design, the 6 series is equipped with this electronic component. Circuits based on SPDT switching are used to construct these analog switch ics. Use NLVAS4599 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 30Ohm. You can find the functions of the 6 pins in the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 2V. 1μA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2V~5.5V. The electronic component can function from 5V. A 1 input needs to be operated. The analog switch ics has 2 outputs. The Automotive, AEC-Q100 series contains it.
NLVAS4599DFT2G Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 220MHz
NLVAS4599DFT2G Applications
There are a lot of ON Semiconductor NLVAS4599DFT2G Analog Switches & Multiplexers ICs applications.
- PBXs
- Relay replacements
- SONET
- DSLAMs
- Routers
- Channel Banks
- Data Acquisition Systems
- Remote wireless modules
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Industrial and process control systems