NLVHC1G66MUR2G
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 40Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLVHC1G66 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 25mA |
| Max Supply Current | 25mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 40 ns |
| Supply Type | Single |
| Bandwidth | 150MHz |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 180MHz |
| On-State Resistance (Max) | 40Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| Switch Circuit | SPST - NO |
| Switch-on Time-Max | 50ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.55mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
NLVHC1G66MUR2G Overview
The electronic part can be shipped overseas conveniently because it is packaged in 6-UFDFN. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to -55°C~125°C TA. In total, there have been 6 terminations. A electrical component with 1 channels is capable of high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. A key feature of the 6 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NO switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 1. Try searching for the analog switch ic with NLVHC1G66 if you are looking for variants. It has an internal resistance of 40Ohm. For details about the functions of 6 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 2V. An operating current of 1μA would be sufficient for this switch device. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. Putting voltage greater than 25mA on the multiplexer may cause damage. A voltage of 5V can be used to operate the electronic component. 150MHz bandwidths enable data to be transferred. This is electronic component of the Automotive, AEC-Q100 series.
NLVHC1G66MUR2G Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 180MHz
Bandwidth: 150MHz
NLVHC1G66MUR2G Applications
There are a lot of ON Semiconductor NLVHC1G66MUR2G Analog Switches & Multiplexers ICs applications.
- HDTV
- Data switching
- Fault Tolerant Systems
- Industrial control systems
- Relay Replacement
- Communications systems
- New designs requiring multiplexer functions
- Voice over IP/DSL – Integrated Access Devices, Smart
- ATM
- Mechanical reed relay replacement
