NX3L1G66GM,132
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 6-XFDFN |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.65V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NX3L1G66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 6 |
| JESD-30 Code | R-PDSO-N6 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 4.3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| -3db Bandwidth | 60MHz |
| On-State Resistance (Max) | 750mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 35pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 23ns, 8ns |
| Charge Injection | 6pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 48ns |
| Voltage - Supply, Single (V+) | 1.4V~4.3V |
| Normal Position | NO |
| Height Seated (Max) | 0.5mm |
| RoHS Status | ROHS3 Compliant |
NX3L1G66GM,132 Overview
The electronic component is convenient to ship overseas because it is packed in a 6-XFDFN. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~125°C TA extended. 6 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. An 1.65V voltage supply should allow the electrical part to be turned on and run. A total of 6 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO switching circuits. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with NX3L1G66. The analog multiplexer shown here is a typical Multiplexer or Switches. This analogue multiplexer requires a voltage of 1.4V~4.3V when it drains from a single voltage supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
NX3L1G66GM,132 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 60MHz
NX3L1G66GM,132 Applications
There are a lot of NXP USA Inc. NX3L1G66GM,132 Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Signal routing between systems
- PCMCIA cards
- Industrial
- Switching Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- PBXs
- E1 Network Equipment
- Precision test equipment
- Channel Banks
