NX3L1T5157GM,115
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 6-XFDFN |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 1.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | NX3L1T5157 |
| Pin Count | 6 |
| JESD-30 Code | R-PDSO-N6 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 4.3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| -3db Bandwidth | 60MHz |
| On-State Resistance (Max) | 750mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 35pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 40ns, 20ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 20m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 1.4V~4.3V |
| Height Seated (Max) | 0.5mm |
| RoHS Status | ROHS3 Compliant |
NX3L1T5157GM,115 Overview
Due to its 6-XFDFN packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. 6 terminations have been made so far. A high-quality output is provided by the electrical component's 1 channels. Powered by a 1.5V voltage supply, the electrical part should be switched on and run. There are 6 pins injected into the electronic part body. These analog multiplexers are built based on SPDT switching circuits. A 1 circuit is present in this switch device. Using the NX3L1T5157 search parameter, you can discover variants of the switch. Multiplexer or Switches is a typical switch device. This analog switch requires a voltage of 1.4V~4.3V to drain from a single voltage supply.
NX3L1T5157GM,115 Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 60MHz
NX3L1T5157GM,115 Applications
There are a lot of NXP USA Inc. NX3L1T5157GM,115 Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- PCMCIA cards
- Data Acquisition Systems
- Microprocessor Controlled Analog Systems
- Routers
- Industrial
- DSLAMs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Access Concentrators
- E1 Network Equipment
