OMAPL138BZCED4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | 361-LFBGA |
| Number of Pins | 361 |
| Weight | 789.392471mg |
| Operating Temperature | -40°C~90°C TJ |
| Packaging | Tray |
| Series | OMAP-L1x |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 361 |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Other uPs/uCs/Peripheral ICs |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1V |
| Terminal Pitch | 0.65mm |
| Frequency | 456MHz |
| Base Part Number | OMAPL138 |
| Pin Count | 361 |
| Operating Supply Voltage | 1.3V |
| Voltage | 1.35V |
| Interface | I2C, Parallel, SPI, USB |
| Max Supply Voltage | 1.35V |
| Min Supply Voltage | 1.25V |
| RAM Size | 8kB |
| uPs/uCs/Peripheral ICs Type | DIGITAL SIGNAL PROCESSOR, OTHER |
| Core Processor | ARM926EJ-S |
| Data Bus Width | 32b |
| Number of Timers/Counters | 3 |
| Core Architecture | ARM |
| Boundary Scan | YES |
| Low Power Mode | YES |
| Format | FLOATING POINT |
| Voltage - I/O | 1.8V 3.3V |
| Ethernet | 10/100Mbps (1) |
| Number of Cores/Bus Width | 1 Core 32-Bit |
| Graphics Acceleration | No |
| RAM Controllers | SDRAM |
| USB | USB 1.1 + PHY (1), USB 2.0 + PHY (1) |
| Additional Interfaces | HPI, I2C, McASP, McBSP, MMC/SD, SPI, UART |
| Co-Processors/DSP | Signal Processing; C674x, System Control; CP15 |
| Number of Cores | 2 |
| Barrel Shifter | NO |
| Internal Bus Architecture | MULTIPLE |
| Security Features | Boot Security, Cryptography |
| Display & Interface Controllers | LCD |
| SATA | SATA 3Gbps (1) |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OMAPL138BZCED4 Overview
The embedded microprocessor ships overseas conveniently packed in 361-LFBGA. High reliability is achieved using advanced packaging method Tray. The CPU has 1 Core 32-Bit cores/Bus width. Extended operating temperature around -40°C~90°C TJ. From the OMAP-L1x series. A ARM926EJ-S processor is present in this CPU. There are SDRAM RAM controllers used by this CPU. This microprocessor features interfaces HPI, I2C, McASP, McBSP, MMC/SD, SPI, UART. As far as I/O is concerned, this CPU runs at 1.8V 3.3V. uPs/uCs/Peripheral ICs are a DIGITAL SIGNAL PROCESSOR, OTHER. Use OMAPL138 when searching for variants of the embedded microprocessor. In total, 361 terminations have been made. With a 1V voltage supply, the part should be turned on and run. There is 456MHz frequency set for the CPU. You can refer to the datasheets for the functions of 361 pins. As a Other uPs/uCs/Peripheral ICs, this cpu microprocessor is typical. It is important to note that there is 32b bandwidth available for data transfer. A total of 361 pins are injected into the CPU microprocessor's body. It has 2 cores. This CPU is widely used in a variety of applications with its Surface Mount mounting. From 1.3V, the micro processor can be used. 1.35V is the voltage on the CPU core. A 8kB amount of RAM (Random-Access Memory) is designed. In a normal situation, users should not supply the CPU microprocessor with a voltage higher than 1.35V. There should be 1.25V voltage applied to the CPU microprocessor below 1.25V. Counters 3 indicate how busy the CPU is.
OMAPL138BZCED4 Features
ARM926EJ-S Core
32b-Bit Data Bus Width
2-Core CPU
8kB RAM
OMAPL138BZCED4 Applications
There are a lot of Texas Instruments OMAPL138BZCED4 Microprocessor applications.
- Network communication, mobile communication field
- Information appliances (networking of household appliances)
- Electronic jamming systems
- Industrial control field
- Safety -airbags, automatic braking system (ABS)
- Office automation equipment and computer peripherals
- Volt meter
- Metering & measurement field
- Robots
- Telephone sets
