OP213ESZ-REEL7
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP213 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 6mA |
| Nominal Supply Current | 2.7mA |
| Quiescent Current | 3mA |
| Slew Rate | 1.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 96 dB |
| Current - Input Bias | 240nA |
| Voltage - Supply, Single/Dual (±) | 4V~36V ±2V~18V |
| Output Current per Channel | 40mA |
| Supply Type | Dual, Single |
| Input Offset Voltage (Vos) | 100μV |
| Gain Bandwidth Product | 3.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3400 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.7μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Settling Time | 9 μs |
| Bias Current-Max (IIB) @25C | 0.65μA |
| Dual Supply Voltage | 15V |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
OP213ESZ-REEL7 Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. We are approaching the 8h termination of the year. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 15V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are available on the instrumentation amplifier. Op amp rates 100μV as input offset voltage. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureThis op amp can operate from a supply current at 6mA. 126.02dB should remain the voltage gain. The op amp ic has 2 channels on it. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 5V. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. Linear amplifier has a quiescent current of 3mA.
OP213ESZ-REEL7 Features
8 Pins
supply voltage of 15V
126.02dB voltage gain
Output Type: Rail-to-Rail
OP213ESZ-REEL7 Applications
There are a lot of Analog Devices Inc. OP213ESZ-REEL7 Instrumentational OP Amps applications.
- Proportional operation circuits
- Television broadcasting equipment
- Hand-held batteries
- Weighing systems
- High/low-pass filter circuit
- Signal transformation
- E-book readers
- Multiplication circuits
- Wireless base stations
- Tablets
