OP27AFKB
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Lead, Tin |
| Surface Mount | YES |
| Number of Pins | 20 |
| Packaging | Bulk |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Operational Amplifier |
| Packing Method | TUBE |
| Technology | BIPOLAR |
| Terminal Position | QUAD |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Pin Count | 20 |
| Temperature Grade | MILITARY |
| Number of Channels | 1 |
| Max Supply Voltage | 22V |
| Power Dissipation-Max | 1.375W |
| Supply Current-Max | 3.2mA |
| Slew Rate | 2.8 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 114 dB |
| Current - Input Bias | 40nA |
| Gain Bandwidth Product | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 125.11dB |
| Average Bias Current-Max (IIB) | 0.06μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 22V |
| Low-Bias | NO |
| Micropower | NO |
| Min Dual Supply Voltage | 4V |
| Bias Current-Max (IIB) @25C | 0.04μA |
| Programmable Power | NO |
| Screening Level | 38535Q/M;38534H;883B |
| Dual Supply Voltage | 15V |
| Nominal Gain Bandwidth Product | 8MHz |
| Max I/O Voltage | 25μV |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.035μA |
| Height | 2.03mm |
| Length | 8.89mm |
| Width | 8.89mm |
| Thickness | 1.83mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
OP27AFKB Overview
There are two types of operational amplifiers in this circuit. Upon delivery, op amp ic is packaged in a Bulk case. We are approaching the 20h termination of the year. Linear amplifier has a total of 20 pins. Please take in mind that op amp should be run at 15V. It should be noted that this op amp is a type of Operational Amplifier device. 20 pins are included on the operational amplifiers. There should be no change in the voltage gain at 125.11dB. Buffer op amp is equipped with 1 channels on the device. For this linear amplifier to work, the temperature should not be below -55°C. You should not use op amp above 125°C . TUBE is adopted to pack the instrumentation amplifier. I would like to point out that this electrical component is capable of working from a voltage below 22V as far as the power supply is concerned. There should be a dual supply voltage of 22V for you to conduct this electrical part.
OP27AFKB Features
20 Pins
supply voltage of 15V
125.11dB voltage gain
OP27AFKB Applications
There are a lot of Texas Instruments OP27AFKB Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Test equipment
- Signal amplification
- Voltage regulation circuit
- Weak signal detection
- Portable media players
- Gaming industry
- Oscilloscopes
- Proportional operation circuits
- Inverse/same-phase proportional circuit
