OP27AZ/883C
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tube |
| Series | Military, MIL-STD-883 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn63Pb37) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OP27 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 5.7mA |
| Nominal Supply Current | 5.7mA |
| Quiescent Current | 5.7mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 10nA |
| Voltage - Supply, Single/Dual (±) | ±4V~18V |
| Input Offset Voltage (Vos) | 25μV |
| Bandwidth | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 125.11dB |
| Average Bias Current-Max (IIB) | 0.06μA |
| Power Supply Rejection Ratio (PSRR) | 114dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 10μV |
| Bias Current-Max (IIB) @25C | 0.04μA |
| Dual Supply Voltage | 5V |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Input Voltage Noise Density | 3.5nV/sqrt Hz |
| Height | 3.56mm |
| Length | 10.29mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP27AZ/883C Overview
The linear amplifier is packaged in a 8-CDIP (0.300, 7.62mm) case. A General Purpose-type buffer amplifier is shown here. Linear amplifier is delivered in a Tube case. The number of terminations approaches 8. In this case, there are 8 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. 8 pins are located on the operational amplifiers. There is an input offset voltage of 25μV for this buffer op amp. This electronic component is recommended to be mounted using the mounting type Through Hole. It is recommended that this op amp ic be operated at a temperature no higher than -55°C~125°C for optimal performance. You can run this op amp ic on 5.7mA . Keeping the voltage gain at 125.11dB is the best course of action. There are 1 elements in this buffer amplifier. The Military, MIL-STD-883 stands for the buffer op amp's serial number. There is a quiescent current of 5.7mA in this operational amplifier circuit.
OP27AZ/883C Features
8 Pins
supply voltage of 15V
125.11dB voltage gain
OP27AZ/883C Applications
There are a lot of Analog Devices Inc. OP27AZ/883C Instrumentational OP Amps applications.
- Computer workstations
- Information processing
- Fission chambers
- Commercial audio systems
- Medical instruments
- Vehicle electronics
- Hand-held batteries
- Portable docking station
- Gaming industry
- Video computer boards
