OP27GPZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 170mW |
| Technology | BIPOLAR |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OP27 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 5.7mA |
| Nominal Supply Current | 4.67mA |
| Quiescent Current | 5.7mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 15nA |
| Max Input Voltage | 11V |
| Voltage - Supply, Single/Dual (±) | ±4V~18V |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 25μV |
| Bandwidth | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 123.52dB |
| Power Supply Rejection Ratio (PSRR) | 114dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 30μV |
| Dual Supply Voltage | 18V |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Height | 3.43mm |
| Length | 9.27mm |
| Width | 7.24mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP27GPZ Overview
Packaged in a 8-DIP (0.300, 7.62mm) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tube case. There is a growing number of terminations approaching the number of 8. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 25μV. This electronic part is best mounted with type Through Hole. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Operational amplifier can operate supply current at 5.7mA. There should be no change in the voltage gain. On the buffer amps, there are 1 channels that can be used. The current is quiescent at 5.7mA.
OP27GPZ Features
8 Pins
supply voltage of 15V
123.52dB voltage gain
OP27GPZ Applications
There are a lot of Analog Devices Inc. OP27GPZ Instrumentational OP Amps applications.
- Band-pass filter
- Integrator circuits
- Micro signal measurement
- Division circuits
- Automatic control
- Tablets
- Computer workstations
- ECG equipment
- Radiation thermometry transducers
- Proportional operation circuits
