OP27GS-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 170mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP27 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Quiescent Current | 5.7mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | ±4V~18V |
| Input Offset Voltage (Vos) | 30μV |
| Gain Bandwidth Product | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 123.52dB |
| Power Supply Rejection Ratio (PSRR) | 113.98dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Dual Supply Voltage | 5V |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Input Voltage Noise Density | 3.8nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP27GS-REEL Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 8. It consists of a total of 8 pins in total. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. Instrumentation amplifier is a part of Operational Amplifier. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 30μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. There should be no change in the voltage gain at 123.52dB. Buffer op amp is equipped with 1 channels on the device. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. Currently, linear amplifier is operating with a quiescent current of 5.7mA.
OP27GS-REEL Features
8 Pins
supply voltage of 15V
123.52dB voltage gain
OP27GS-REEL Applications
There are a lot of Analog Devices Inc. OP27GS-REEL Instrumentational OP Amps applications.
- Home audio systems
- Measurements of Wheatstone bridge
- Micro signal measurement
- Proportional counter tubes
- single/dual op amp sum and difference circuits
- Strain gauges
- PDA
- High/low-pass filter circuit
- Power generator
- Tablets
