OP27GS-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 170mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP27 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 5.7mA |
| Quiescent Current | 5.7mA |
| Slew Rate | 2.8V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | ±4V~18V |
| Input Offset Voltage (Vos) | 25μV |
| Gain Bandwidth Product | 8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 8000 kHz |
| Voltage Gain | 123.52dB |
| Power Supply Rejection Ratio (PSRR) | 114dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 30μV |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Input Voltage Noise Density | 3.8nV/sqrt Hz |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP27GS-REEL7 Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Op amps are General Purpose types of amplifier on the chip. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. The number of terminations approaches 8. The total number of pins on linear amplifier is 8. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are included on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 25μV. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureOperational amplifier can operate supply current at 5.7mA. It is a member of the 123.52dB's 123.52dB family. There are a total of 1 channels available on the op amps. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. There is a quiescent current of 5.7mA in this operational amplifier circuit.
OP27GS-REEL7 Features
8 Pins
supply voltage of 15V
123.52dB voltage gain
OP27GS-REEL7 Applications
There are a lot of Analog Devices Inc. OP27GS-REEL7 Instrumentational OP Amps applications.
- Fission chambers
- Micro signal measurement
- Digital cameras
- Division circuits
- High-frequency data acquisition systems
- Signal filtering
- Test equipment
- Exponential operation circuits
- Television
- High speed sample
