OP282ARMZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~90°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP282 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 2 |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 250μA |
| Quiescent Current | 250μA |
| Slew Rate | 9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 12mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 86.02dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 1.6 μs |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Dual Supply Voltage | 15V |
| Input Voltage Noise Density | 36nV/sqrt Hz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP282ARMZ-REEL Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. A J-FET-type buffer amplifier is shown here. The op amp is delivered to you in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. It is important to remember that this op amp should be operated at a voltage of 15V volts. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 8 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electronic part is best mounted with type Surface Mount. The buffer amplifier functions well at -40°C~90°C as far as operating temperature is concerned. It is possible to operate this buffer amplifier from a supply current of 500μA . Voltage gain should remain at 86.02dB. On the buffer amps, there are 2 channels that can be used. The operating supply voltage of instrumentation amplifier is rated 18V voltage. TAPE AND REEL is adopted to pack the instrumentation amplifier. There is a quiescent current of 250μA in this operational amplifier circuit.
OP282ARMZ-REEL Features
8 Pins
supply voltage of 15V
86.02dB voltage gain
OP282ARMZ-REEL Applications
There are a lot of Analog Devices Inc. OP282ARMZ-REEL Instrumentational OP Amps applications.
- Test and measurement instruments
- Tablets
- Video data acquisition
- Laptop
- Micro signal measurement
- Instrumentation
- Addition operation circuits
- Industrial applications including automation
- Digital cameras
- Multiplication circuits
