OP293FSZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP293 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/+-15V |
| Number of Channels | 2 |
| Operating Supply Current | 60μA |
| Max Supply Current | 29μA |
| Quiescent Current | 30μA |
| Slew Rate | 0.015V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 116 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 1.7V~36V ±0.85V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 35 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 35 kHz |
| Voltage Gain | 106.02dB |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 250μV |
| Micropower | YES |
| Dual Supply Voltage | 9V |
| Input Voltage Noise Density | 65nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP293FSZ Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Op amps are General Purpose types of amplifier on the chip. A Tube case is used to deliver the buffer op amp. The number of terminations is approaching the 8 mark. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 15V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 8 pins are located on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 200μV. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 60μA and 10 . 106.02dB should remain the voltage gain. There are 2 channels on the operational amplifiers. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The operating supply voltage of instrumentation amplifier is rated 18V voltage. As a result, linear amplifier's quiescent current is 30μA.
OP293FSZ Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
Output Type: Rail-to-Rail
OP293FSZ Applications
There are a lot of Analog Devices Inc. OP293FSZ Instrumentational OP Amps applications.
- Video amplifiers
- ECG equipment
- Communication
- High-frequency data acquisition systems
- High input resistance broadband
- Switching amplifier
- Fission chambers
- Signal amplification
- Cinema or auditorium audio system
- Commercial audio systems
