OP4177AR-REEL7
| Parameters | |
|---|---|
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP4177 |
| Pin Count | 14 |
| Power Supplies | +-5/+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 2mA |
| Quiescent Current | 500μA |
| Slew Rate | 0.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 125 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 75μV |
| Gain Bandwidth Product | 1.3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 125dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 15μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Wideband | NO |
| Input Voltage Noise Density | 7.9nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
OP4177AR-REEL7 Overview
In order to protect the op amps, a 14-SOIC (0.154, 3.90mm Width) case is used. A General Purpose-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 14. Buffer amplifier has a total of 14 pins on it. This linear amplifier should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The op amp ic has an array of 14 pins on it. Regarding input offset voltage, buffer amplifier rates 75μV voltage. This electrical part should be mounted using type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 2mA supply current, this operational amplifier ics can be operated. The voltage gain should stay at 126.02dB. The op amp ic has 4 channels on it. It is used TAPE AND REEL to pack the op amps. There is a quiescent current of 500μA in this operational amplifier circuit.
OP4177AR-REEL7 Features
14 Pins
supply voltage of 5V
126.02dB voltage gain
OP4177AR-REEL7 Applications
There are a lot of Analog Devices Inc. OP4177AR-REEL7 Instrumentational OP Amps applications.
- Oscilloscopes
- Vehicle electronics
- Radiation thermometry transducers
- Polarized electrodes
- High-frequency data acquisition systems
- Test equipment
- Mobile phone
- Power control
- High/low-pass filter circuit
- Logarithmic operation circuits
