OP42AZ
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | TIN LEAD |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | OP42 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Operating Supply Current | 5.1mA |
| Nominal Supply Current | 6mA |
| Quiescent Current | 6.5mA |
| Slew Rate | 52V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 92 dB |
| Current - Input Bias | 80pA |
| Voltage - Supply, Single/Dual (±) | ±8V~20V |
| Output Current per Channel | 33mA |
| Input Offset Voltage (Vos) | 300μV |
| Gain Bandwidth Product | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 119.08dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Power Supply Rejection Ratio (PSRR) | 100.92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 6pF |
| Input Offset Current-Max (IIO) | 0.00004μA |
| Height | 3.56mm |
| Length | 10.29mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP42AZ Overview
It is packaged in an 8-CDIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. Op amps are J-FET types of amplifier on the chip. A Tube case is used for delivering the op amp. There have been a total of 8 terminations over the past year. The total number of pins on linear amplifier is 8. It is important to remember that this op amp should be operated at a voltage of 15V volts. This particular linear amplifier is a type of Operational Amplifier device, to be precise. A total of 8 pins are present on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 300μV. For this electrical component, Through Hole is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -55°C~125°C , which is a good operating temperature. This op amp can operate from a supply current at 5.1mA. There should be no change in the voltage gain at 119.08dB. As far as the device is concerned, buffer amplifier has 1 channels. The operating supply voltage of the buffer op amp is rated at 15V. There is a quiescent current of 6.5mA in this operational amplifier circuit.
OP42AZ Features
8 Pins
supply voltage of 15V
119.08dB voltage gain
OP42AZ Applications
There are a lot of Analog Devices Inc. OP42AZ Instrumentational OP Amps applications.
- Subtraction operation circuits
- Vehicle electronics
- Image computer boards
- Large motor controllers
- Logarithmic operation circuits
- Fission chambers
- pH (acidity)
- Test and measurement instruments
- Commercial audio systems
- Precision measurement
