OP42GSZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP42 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Operating Supply Current | 6.5mA |
| Nominal Supply Current | 6.5mA |
| Quiescent Current | 5.1mA |
| Slew Rate | 50V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 92 dB |
| Current - Input Bias | 130pA |
| Voltage - Supply, Single/Dual (±) | ±8V~20V |
| Output Current per Channel | 33mA |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 1.2mV |
| Gain Bandwidth Product | 10MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 119.08dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 1.5mV |
| Settling Time | 800 ns |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00025μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 6pF |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP42GSZ-R7 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. Op amps are J-FET types of amplifier on the chip. A Tape & Reel (TR) case is used for delivering the op amp. There have been a total of 8 terminations over the past year. In this case, there are 8 pins on the board. This linear amplifier should be powered by an 15V battery. Instrumentation amplifier is a part of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 1.2mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 6.5mA . 119.08dB should be the voltage gain. Op amp ic has 1 channels. The operating supply voltage of instrumentation amplifier is rated 15V voltage. This linear amplifier pack is based on the TAPE AND REEL axis. There is an 5.1mA quiescent current running through op amp ic.
OP42GSZ-R7 Features
8 Pins
supply voltage of 15V
119.08dB voltage gain
OP42GSZ-R7 Applications
There are a lot of Analog Devices Inc. OP42GSZ-R7 Instrumentational OP Amps applications.
- Vehicle electronics
- Signal amplification
- High/low-pass filter circuit
- Mobile phone
- MP3
- Image computer boards
- Measurements of Wheatstone bridge
- Micro signal measurement
- Hand-held batteries
- Differentiator circuits
