OP462HRU-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP462 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Operating Supply Current | 550μA |
| Quiescent Current | 775μA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 260nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±1.35V~6V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 25μV |
| Gain Bandwidth Product | 15MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 15000 kHz |
| Voltage Gain | 98.89dB |
| Average Bias Current-Max (IIB) | 0.65μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Bias Current-Max (IIB) @25C | 0.0006μA |
| Neg Supply Voltage-Max (Vsup) | -6V |
| Input Voltage Noise Density | 9.5nV/sqrt Hz |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP462HRU-REEL Overview
Packaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. An op amp of this type is a General Purpose-type. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. The number of terminations approaches 14. In total, there are 14 pins on this op amp ic. This linear amplifier should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 14-pin op amp ic is included in the package. Op amp rates 25μV as input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAn 550μA volt supply current is needed for this linear amplifier to operate. Keeping the voltage gain at 98.89dB is the best course of action. As far as the device is concerned, buffer amplifier has 4 channels. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. As a result of this, the buffer amplifier is packed in TAPE AND REEL. There is a quiescent current of 775μA in this operational amplifier circuit.
OP462HRU-REEL Features
14 Pins
supply voltage of 5V
98.89dB voltage gain
Output Type: Rail-to-Rail
OP462HRU-REEL Applications
There are a lot of Analog Devices Inc. OP462HRU-REEL Instrumentational OP Amps applications.
- Displayers for aircraft and air transportation control systems
- Large motor controllers
- High/low-pass filter circuit
- Multiplication circuits
- single/dual op amp sum and difference circuits
- Signal amplification
- Radar
- Television broadcasting equipment
- Video computer boards
- Industrial applications including automation
